Air conditioner cleaning
Service and disinfection.
OpenAir conditioner not cooling in Batumi
Why cooling is weak, what to check, and when to call a technician. On-site service in Batumi. Diagnostics at your location.
Common causes
- • Dirty filters or evaporator.
- • Low refrigerant (leak).
- • Fan or compressor issues.
- • Wrong mode or sensor errors.
What you can check
- • Clean the filters.
- • Check cooling mode and temperature.
- • Make sure the outdoor unit is not blocked.
When to call a technician
- • No improvement after cleaning.
- • Errors or leaks appear.
- • Strong noise, smell, or vibration.
When to stop using the appliance
- • Check Cool mode and visible filters.
- • Do not add refrigerant without diagnostics.
- • Tell us whether the indoor unit leaks water.
What to prepare before contacting us
- • We separate dirty filters/drainage from refrigerant leak, board error or outdoor-unit issues.
Common user mistakes
- • The first mistake is to set minimum temperature for hours immediately. The appliance keeps working under load while the cause remains.
- • The second mistake is to wash the indoor unit without protecting electronics. It can make the component harder to inspect and complicate diagnostics.
- • The third mistake is to add refrigerant without finding the reason. Before any check, power, water/gas and workspace safety matter.
What not to do
- • Do not open closed assemblies if you do not know where the fasteners, sensors and wires are located.
- • Do not buy a part based only on forum advice: similar symptoms often have different causes.
- • Do not hide previous DIY attempts from the technician: it saves time and reduces repeat mistakes.
When to call a technician urgently
- • Call a technician sooner if water drips from the unit or cracking sounds appear. In this situation it is better to stop the appliance and not wait for another cycle.
- • Urgent service is especially important in upper-floor apartments and kitchens with tight built-in furniture.
- • Batumi humidity also matters: after a leak or condensate, contacts oxidize faster.
DIY repair risks
- • The main DIY risk is that you can wet the wall, board and worsen a leak. After that, repair can cost more than the first diagnostic visit.
- • Built-in appliances add risk: cabinet fronts, hoses, cables or nearby kitchen modules can be damaged.
- • The safe minimum before a visit is to disconnect power, close water or gas if needed, and clear access to the appliance.
What to prepare before the technician arrives
- • Clear access to the room: remove mats, baskets, dishes or food near the appliance so the technician can inspect the air conditioner without unnecessary furniture work.
- • Write down the model and approximate age. If there is an error on the display, take a photo before switching the appliance off; it helps connect the symptom to a specific component.
- • Explain when the issue appeared: after moving, voltage drop, cleaning, leakage, long idle period or a normal cycle. These details often shorten diagnostics.
- • For built-in appliances, check whether doors, kickboards or side panels can be opened. In Batumi seaside apartments, tight kitchen layouts often affect repair time.
How on-site diagnostics usually works
- • Diagnostics starts with safe checks: power, connection, visible water traces, overheating signs or mechanical damage. Internal assemblies are checked only after that.
- • For cooling, the technician checks the filters, evaporator, fan, drain and system pressure. The sequence goes from simple to complex to avoid replacing working parts.
- • When the cause is found, the technician shows the failed part or test result, explains repair options and agrees the price before the main work starts.
- • At the end, a short test is needed: program start, heating, draining, cooling or ignition. Without this test it is hard to confirm that the issue is fixed.
What affects the final cost
- • The price depends not only on the fault name, but also on model, access to the component, condition of fasteners, moisture traces and whether a spare part is needed.
- • For apartments in the center, Khimshiashvili, New Boulevard, Boni, Airport area and Gonio, on-site diagnostics is often easier than moving the appliance.
- • If the repair is not worth it after inspection, the technician should say so before any part is purchased. This matters for older appliances and rare models.
- • Prices on the page give a realistic range, but the final cost is fixed only after checking the exact appliance and agreeing the work scope.
Diagnostic workflow
How to separate a safe check from a technician-level fault.
1
We separate dirty filters/drainage from refrigerant leak, board error or outdoor-unit issues.
2
Check Cool mode and visible filters.
3
Do not add refrigerant without diagnostics.
4
Tell us whether the indoor unit leaks water.
Price guide
- Basic cleaning from 70 GEL
- Full cleaning from 100 GEL
- Leak diagnostics by agreement
Cost depends on condition and access.
FAQ
How often should I clean it?
Usually 1–2 times per year.
Can I just add refrigerant?
First the leak must be found and fixed.
WhatsApp
Viber
Telegram
